Chamfer bit 38.1 mm 45°
JVL Chamfer bit 38.1 mm 45° with 8mm shank
JVL Chamfer bit 38.1 mm 45° with 8mm shank
Filter By
Availability
Bore
Shank
Diameter (D)
Cutting length/height:
Total Length
Radius / Angle
Cutters
There are 87 products.
JVL Chamfer bit 38.1 mm 45° with 8mm shank
JVL Chamfer bit 38.1 mm 45° with 8mm shank
Suitable for: Steel, Stainless steel, Cast iron, aluminum,...
Suitable for: Steel, Stainless steel, Cast iron, aluminum, copper and plastics
Cornerround knife radius 2mm D.16 x 16,5 x 2 R=2 Biesse Akron...
Cornerround knife radius 2mm D.16 x 16,5 x 2 R=2 Biesse Akron 1 piece
Suitable for: Steel, Stainless steel, Cast iron, aluminum,...
Suitable for: Steel, Stainless steel, Cast iron, aluminum, copper and plastics
Suitable for: Steel, Stainless steel, Cast iron, Aluminum and...
Suitable for: Steel, Stainless steel, Cast iron, Aluminum and copper
EPROCUT Rounding over bit HW Z=2 D=16,7 R=2 L=8 GL=40 S=8
EPROCUT Rounding over bit HW Z=2 D=16,7 R=2 L=8 GL=40 S=8
Knife in HW 16.5x16x2 R=2 CCEN700007
Knife in HW 16.5x16x2 R=2 CCEN700007
Knife in HW R=2 N3402N0125
Knife in HW R=2 N3402N0125
Two flute rounding over cutter with an exchangeable bearing...
Two flute rounding over cutter with an exchangeable bearing with 12.7 mm. For precise and clean rounded edges.
Bevel cutter for folding and chamfering wood, laminate and...
Bevel cutter for folding and chamfering wood, laminate and plastic sheets.
Knife in HW R=2 CSEN700020
Knife in HW R=2 CSEN700020
Knife in HW R=2 CSEN700019
Knife in HW R=2 CSEN700019
Knife in HW R=1/2/25 degrees CSEN700026
Knife in HW R=1/2/25 degrees CSEN700026
Knife in HW R=1/2/25 degrees CSEN700025
Knife in HW R=1/2/25 degrees CSEN700025
For use on twist drills with a 10 mm shank and a diameter of 4...
For use on twist drills with a 10 mm shank and a diameter of 4 mm to 10 mm.The countersinkis guided to the shank via the drill spiral and fastened there.
For use on twist drills with a 10 mm shank and a diameter of 4...
For use on twist drills with a 10 mm shank and a diameter of 4 mm to 10 mm.The countersinkis guided to the shank via the drill spiral and fastened there.
Ball nose Spiral cutter Z1 Positive - Upcut for Plastics...
Ball nose Spiral cutter Z1 Positive - Upcut for Plastics Suitable for: Acrylonitrile butadiene styrene (ABS) Polycarbonate Polyethylene Polypropylene Polystyrene Polyvinyl chloride (PVC) Polymethyl methacrylate (Acrylic. Plexi etc.)
ENT 13821 Chamfer cutter 45 degrees with ball bearing and 8...
ENT 13821 Chamfer cutter 45 degrees with ball bearing and 8 mm shank
ENT 13801 Chamfer cutter 45 degrees with ball bearing and 6...
ENT 13801 Chamfer cutter 45 degrees with ball bearing and 6 mm shank
For milling a shadow gap or water surge at the basin and water...
For milling a shadow gap or water surge at the basin and water drainage channels on the sink.
Edge scraper with anti-bleaching profile R=2 3402A0126
Edge scraper with anti-bleaching profile R=2 3402A0126
Miniature bevel cutter with bearing 45 degrees
Miniature bevel cutter with bearing 45 degrees
For chamfering thin sheets, plywood, acrylic, etc. For...
For chamfering thin sheets, plywood, acrylic, etc. For interior and exterior contours.
Miniature bevel cutter with bearing 45 degrees
Miniature bevel cutter with bearing 45 degrees
Miniature bevel cutter with bearing 45 degrees
Miniature bevel cutter with bearing 45 degrees
For chamfering thin sheets, plywood, acrylic, etc. For...
For chamfering thin sheets, plywood, acrylic, etc. For interior and exterior contours.